MTP R 15HD RSA D • Setup Guide
This guide provides basic instructions for an experienced installer to set up and operate
the Extron MTP R 15HD RSA D receiver.
Pre-installation
T568A
T568B
Pins:
12345678
Pin Wire color
Wire color
The MTP R 15HD RSA D receiver can be installed in a one-gang electrical wall box with
a Decora wall plate cover (supplied).
1
White-green
Green
White-orange
Orange
2
3
4
5
Choose a location that allows cable runs without interference. Allow enough depth for
both the wall box and the cables. The box should be at least 2.5 inches (6.4 cm) deep
to accommodate the connectors and cables. Install the cables into the wall, furniture,
or conduits before installing the receiver.
White-orange White-green
Blue
Blue
White-blue
Orange
White-blue
Green
6
7
8
Insert Twisted
Pair Wires
White-brown White-brown
Brown Brown
The top image at right details the recommended termination of TP cables with RJ-45
connectors in accordance with the TIA/EIA T568A or TIA/EIA T568B wiring standards.
You can use either standard with CAT 5/5e/6 cable, but ensure that you use the same
standard on both ends of the cable.
NOTE: If you are using Enhanced Skew-Free™ AV
cable, use the TIA/EIA T568A standard only.
Power Supply Wiring
Wire the power connector (see the image on the right). Verify the polarity before
POWER
12V
connection by plugging in the power supply with no load and checking the output
with a voltmeter.
xA MAX
Rear
Panel
Smooth
Ridges
A
A
Grounding guidelines
Extron MTP 15HD RSA D products can be adversely affected by electrostatic discharge)
(ESD) if they are not grounded correctly.
3/16"
(5 mm)
Max.
Tie
Wrap
To prevent malfunctions or product damage, an experienced installer can correctly
ground an Extron MTP 15HD RSA D product grounding the power input port. Insert one
end of the grounding wire to the negative or ground pin on the power input connector
(see the image on the right). Tie the other end of the wire to an earth ground.
Ridges
SECTION A–A
Power Supply
Output Cord
Earth
Ground
If you have any questions about how to ground a product in a specific application,
contact an Extron technical support specialist.
For more information and warnings, see “Power supply wiring” in the MTP R 15HD RSA D
User’s Manual.
Installation
MTP 15HD RSA D Rx Rear Panel
Connect/Configure the Rear Panel
a DC power connector — If applicable, plug the external 12 VDC power supply into
2
this 2-pole captive screw connector (see power wiring details above).
b Input connector — Connect the TP cable from the transmitter to this pigtail RJ-45
H SYNC +
V SYNC +
C SYNC
SOG
VIDEO
Bi-RS232
INPUT
female connector (see the table above on the top right to wire the RJ-45 connectors).
3
1
H
V
SYNC
SYNC
SYNC
+
+
C
SOG
VIDEO
Switches on the next page for more details).
Bi-RS232
|
Edelbrock Automobile Parts 16211 MBN 640 User Manual
Eizo Computer Monitor FlexScan F520 User Manual
Fender Speaker 11040 User Manual
Fisher Price Doll G9157 User Manual
Franke Consumer Products Ventilation Hood FDB 9078 SIL K User Manual
Frigidaire Freezer GLFC1326FW User Manual
FujiFilm Digital Camera 16437542 User Manual
Furuno Telephone FS 5070 User Manual
Garmin Marine GPS System 190 01120 00 User Manual
GE Clothes Dryer DCD330EB User Manual