Vulcan Hart Griddle MGG24 User Manual

INSTALLATION &  
OPERATION MANUAL  
MGG SERIES MEDIUM DUTY  
GAS GRIDDLES  
MODEL  
MGG24  
MGG36  
MGG48  
ML-103818  
ML-103819  
ML-103820  
MGG24  
VULCAN-HART COMPANY, P.O. BOX 696, LOUISVILLE, KY 40201-0696, TEL. (502) 778-2791  
FORM 30993 (10-96) (Formerly 990409)  
 
TABLE OF CONTENTS  
GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Installation Codes and Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Leveling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Gas Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Testing the Gas Supply System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Flue Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Before First Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Lighting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Turning the Griddle On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Using the Griddle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Suggested Temperatures and Times for Griddling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Vent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Service and Parts Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
— 3 —  
 
Installation, Operation and Care of  
MGG SERIES GAS GRIDDLES  
PLEASE KEEP THIS MANUAL FOR FUTURE USE  
GENERAL  
Vulcan griddles are produced with quality workmanship and material. Proper installation, usage and  
maintenance of your griddle will result in many years of satisfactory performance.  
It is suggested that you thoroughly read this entire manual and carefully follow all of the instructions  
provided.  
INSTALLATION  
Before installing, verify that the electrical service and type of gas supply (natural or propane) agree with  
the specifications on the rating plate located inside the griddle door panel. If the supply and equipment  
requirements do not agree, do not proceed with the installation. Contact your dealer or Vulcan-Hart  
Company immediately.  
UNPACKING  
This griddle was inspected before leaving the factory. The transportation company assumes full  
responsibility for safe delivery upon acceptance of the shipment. Immediately after unpacking, check  
for possible shipping damage. If the griddle is found to be damaged, save the packaging material and  
contact the carrier within 15 days of delivery.  
Carefully unpack griddle. Make sure no parts are discarded with crating material. Place griddle in its  
final installed position.  
LOCATION  
The equipment area must be kept free and clear of combustible substances.  
The griddle may be installed on a combustible countertop.  
When installed, minimum clearance from combustible construction must be 3" at the sides and 3" at  
the rear. Minimum clearance from non-combustible construction is 0" at the sides and rear.  
— 4 —  
 
The installation location must allow adequate clearances for servicing and proper operation. A  
minimum front clearance of 32" is required.  
Do not obstruct the flow of combustion and ventilation air. Adequate clearance for air openings into  
the combustion chamber must be provided. Make sure there is an adequate supply of air in the room  
to replace air taken out by the ventilating system.  
Do not permit fans to blow directly at the griddle. Wherever possible, avoid open windows next to the  
griddle. Avoid wall-type fans which create air cross currents within the room.  
INSTALLATION CODES AND STANDARDS  
The griddle must be installed in accordance with:  
In the United States of America:  
1. State and local codes.  
2. National Fuel Gas Code, ANSI-Z223.1 (latest edition). Copies may be obtained from The American  
Gas Association, Inc., 1515 Wilson Blvd., Arlington, VA 22209.  
3. National Electrical Code, ANSI/NFPA-70 (latest edition). Copies may be obtained from The  
National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.  
In Canada:  
1. Local codes.  
2. CAN/CGA-B149.1 Installation for Natural Gas Burning Appliances and Equipment (latest edition).  
3. CAN/CGA-B149.2 Installation for Propane Burning Appliances and Equipment (latest edition),  
available from the Canadian Gas Association, 55 Scarsdale Road, Don Mills, Ontario, Canada  
M3B2R3.  
4. Canadian Electrical Code, Part 2, CSA Standard C22.1 (latest edition). Copies may be obtained  
from The Canadian Standard Association, 178 Rexdale Blvd., Rexdale, Ontario, Canada M9W1R3.  
ASSEMBLY  
The griddle is shipped as a complete unit and does not require field assembly except for the supporting  
legs. Screw the legs into permanently fastened nuts on the four corners of the griddle bottom. Hand  
tighten the legs and set the griddle in place.  
LEVELING  
Place a carpenter's level on top of the griddle. Level the griddle front to back and side to side by turning  
the adjustment screw at the bottom of each leg.  
— 5 —  
 
GAS CONNECTIONS  
CAUTION: Gas supply connections and any pipe joint compound must be resistant to the action  
of propane gases.  
Location of the gas inlet is at the rear of the griddle. Codes require that a gas shutoff valve must be  
installed in the gas line ahead of the griddle.  
Connect gas supply. Make sure the pipes are clean and free of obstructions.  
Griddles are equipped with fixed burner orifices for use with natural or propane gas and no adjustment  
is necessary.  
Natural gas pressure regulators are preset for 4" W.C. (Water Column) supply; propane gas pressure  
regulators are preset for 10" W.C. supply. No further adjustment should be required.  
WARNING: PRIOR TO LIGHTING, CHECK ALL JOINTS IN THE GAS SUPPLY LINE FOR LEAKS.  
USE SOAP AND WATER SOLUTION. DO NOT USE AN OPEN FLAME.  
After piping has been checked for leaks, all piping receiving gas should be fully purged to remove air.  
TESTING THE GAS SUPPLY SYSTEM  
When gas supply pressure exceeds 1/2 psig (3.45 kPa), the griddle and its individual shutoff valve must  
be disconnected from the gas supply piping system.  
When gas supply pressure is 1/2 psig (3.45 kPa) or less, the griddle should be isolated from the gas  
supply system by closing its individual manual shutoff valve.  
FLUE CONNECTIONS  
DO NOT obstruct the flow of flue gases from the flue located on the rear of the griddle. It is  
recommended that the flue gases be ventilated to the outside of the building through a ventilation  
system installed by qualified personnel.  
From the termination of the flue to the filters of the hood venting system, a minimum clearance of 18"  
must be maintained.  
Information on the construction and installation of ventilating hoods may be obtained from the standard  
for "Vapor Removal from Cooking Equipment," NFPA No. 96 (latest edition), available from the  
National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.  
ELECTRICAL CONNECTIONS  
WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE  
APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL  
ELECTRICAL CODES.  
— 6 —  
 
WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE  
DISCONNECT SWITCH INDICATING THAT YOU ARE WORKING ON THE CIRCUIT.  
WARNING: APPLIANCES EQUIPPED WITH A FLEXIBLE ELECTRIC SUPPLY CORD ARE  
PROVIDED WITH A THREE-PRONG GROUNDING PLUG. IT IS IMPERATIVE THAT THIS PLUG BE  
CONNECTED INTO A PROPERLY GROUNDED THREE-PRONG RECEPTACLE. IF THE  
RECEPTACLE IS NOT THE PROPER GROUNDING TYPE, CONTACT AN ELECTRICIAN. DO NOT  
REMOVE THE GROUNDING PRONG FROM THIS PLUG.  
Power supply for electric thermostats is 120 volts, 50/60 Hertz, 1 phase, 5 amperes.  
Do not connect the griddle to electrical supply until after gas connections have been made.  
— 7 —  
 
OPERATION  
WARNING: THE GRIDDLE AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING,  
CLEANING OR SERVICING THE GRIDDLE.  
CONTROLS  
THERMOSTAT — Each thermostat controls the gas flow to the burner to bring that area of the  
griddle plate up to the set temperature.  
BEFORE FIRST USE  
The griddle is shipped covered with a protective coating of grease. Remove this film only when the  
griddle plate is being cleaned prior to its first cooking use. Use a non-corrosive, grease dissolving  
commercial cleaner, following manufacturer's directions. Rinse thoroughly and wipe dry with a soft  
clean cloth. Clean all accessories. Rinse thoroughly and wipe dry.  
Season the griddle to avoid possible surface corrosion. Heat griddle to a low (300-350°F) temperature  
and pour on a small amount of cooking oil (about one ounce per square foot of surface). Use a soft  
lint-free cloth to spread the oil over the entire griddle surface to create a thin film. Wipe off any excess  
oil with a cloth. Repeat the procedure two to three times until the griddle has a slick, mirror-like surface.  
This should also be done after every cleaning.  
LIGHTING INSTRUCTIONS  
Lighting instructions are also inside the front panel. To open the front panel, remove two screws from  
upper front panel. Lift the upper front panel until it clears the lower front panel.  
To reinstall the upper front panel, place panel above lower front panel, slip upper panel down so it  
engages the lower front panel and install screws.  
1. Turn manual shutoff valve OFF.  
2. Turn thermostat to OFF. Wait five minutes to allow gas which may have accumulated in the burner  
compartment to escape.  
3. Turn manual shutoff valve ON.  
4. Depress and hold in on the red button (Fig. 1) on the automatic pilot shutoff valve while lighting the  
pilot burner with a lit taper.  
5. When gas at pilot has been burning for about 45 seconds, release the red button. If pilot does not  
remain lit, repeat Steps 1 through 4, allowing more time before releasing red reset button.  
— 8 —  
 
RED  
BUTTON  
PILOT  
ADJUSTMENT  
SCREW  
PL-52472  
PILOT SHUTOFF VALVE  
Fig. 1  
TURNING THE GRIDDLE ON AND OFF  
Since all burners are lit from constantly burning pilots, turning the thermostats as desired is all that is  
required to put the griddle into service. To turn the griddle off, turn thermostats to OFF.  
Extended Shutdown  
1. Turn all thermostats to OFF.  
2. Extinguish pilot flame by turning the adjusting screw on the pilot shutoff valve (Fig. 1).  
3. Turn manual shutoff valve OFF.  
USING THE GRIDDLE  
Each 12" section of the griddle is independently controlled by a thermostat. Turn the thermostat(s) to  
the desired setting. If different temperature settings are to be used, adjoining areas should be set at  
progressively higher temperatures, the lowest temperature being adjacent to one side. CAUTION:  
DONOToverheatthegriddleplatebysettingthermostatswellaboverecommendedtemperatures.  
Overheating the plate may cause plate warpage and will carbonize the grease on the plate,  
causing sticking. See SUGGESTED TEMPERATURES AND TIMES FOR GRIDDLING in this  
manual.  
Turn the burners on about 15-20 minutes before cooking to preheat.  
A uniform and systematic approach to the loading of the griddle will produce the most consistent  
product results.  
— 9 —  
 
This griddle plate is steel, but the surface is relatively soft and can be scored or dented by carelessly  
using a spatula. Be careful not to dent, scratch, or gouge the plate surface. Do not try to knock off loose  
food that may be on the spatula by tapping the corner or the edge of the spatula on the griddle surface.  
CLEANING  
WARNING: DISCONNECT ELECTRICAL POWER SUPPLY BEFORE CLEANING.  
Empty and clean the grease drawer daily.  
Clean the griddle regularly. A clean griddle looks better, lasts longer and performs better. To produce  
evenly cooked, perfectly browned griddle products, keep the griddle plate clean and free of carbonized  
grease. Carbonized grease on the surface hinders the transfer of heat from the griddle surface to food.  
This results in spotty browning and loss of cooking efficiency. Worst of all, carbonized grease tends  
to cling to the griddled foods, giving them a highly unsatisfactory and unappetizing appearance.  
To keep the griddle clean and operating at peak efficiency, follow these procedures:  
After Each Use  
Clean the griddle with a wire brush or flexible spatula.  
Once a Day  
Thoroughly clean splash back, sides and front. Remove the grease drawer, empty it and wash it out  
in the same manner as any ordinary cooking utensil.  
Once a Week  
Clean the griddle surface thoroughly. If necessary, use a griddle stone, wire brush or use steel wool  
on the surface. Rub with the grain of the metal while the griddle is still warm. A detergent may be used  
on the plate surface to help clean it, but be sure the detergent is thoroughly removed. After removal  
of the detergent, the surface of the plate should be covered with a thin film of oil to prevent rusting.  
Clean stainless steel surfaces with a damp cloth and polish with a soft dry cloth. To remove  
discolorations, use a non-abrasive cleaner.  
After each weekly cleaning, the griddle must be reseasoned.  
If the griddle usage is very high, consider going through the "weekly" cleaning procedures more often  
than once a week.  
Keep burner air shutter openings clean.  
10 —  
 
SUGGESTED TEMPERATURES AND TIMES FOR GRIDDLING  
These are only suggested griddle temperatures and cooking times. You may want to try others. For  
example, some restaurants are cooking hamburgers at 300°F and under.  
CONTROL SETTING  
TIME IN  
MINUTES  
3 to 4  
6
FOOD  
American Fried Potatoes  
Bacon  
(°F)  
375  
350  
Boiled Ham  
375  
2
Beef Tenderloin  
Canadian Bacon  
Hamburgers  
Club Steak  
Ham Steak  
400  
350  
350  
450  
5 to 7  
3 to 4  
3 to 4  
3 to 5  
10  
400  
Sausage Links or Patties  
French Toast  
Pancakes  
350  
400  
375  
3 to 4  
4 to 5  
2
Scrambled Eggs  
Hard Fried Eggs  
Soft Fried Eggs  
Sunny Side Up Eggs  
300  
3 to 4  
3 to 4  
2 to 3  
3 to 4  
225-300  
250-300  
225-300  
MAINTENANCE  
WARNING: THE GRIDDLE AND ITS PARTS ARE HOT. USE CARE WHEN OPERATING,  
CLEANING OR SERVICING THE GRIDDLE.  
WARNING: DISCONNECT ELECTRICAL POWER SUPPLY BEFORE PERFORMING ANY  
MAINTENANCE ON THE GRIDDLE.  
LUBRICATION  
All valves and thermostats must be checked and lubricated periodically. Check with your Vulcan-  
authorized servicer.  
VENT  
Annually, when the griddle is cool, check the flue and clear any obstructions.  
SERVICE AND PARTS INFORMATION  
To obtain service and parts information concerning this griddle, contact the Vulcan-Hart Service  
Agency in your area (refer to listing supplied with the griddle), or Vulcan-Hart Company Service  
Department at the address or phone number shown on the front cover of this manual.  
11 —  
 
TROUBLESHOOTING  
PROBLEM  
POSSIBLE CAUSES  
Heat does not come on when thermostat is  
turned on.  
1. Not plugged in.  
2. Problem with thermostat.  
3. Circuit breaker tripped.  
4. Loose wiring connection.  
5. Pilot burner not lit.  
6. Problem with gas valve.  
Pilot burner will not light.  
Pilot burner will not stay lit.  
1. Manual gas valve not turned on.  
2. Obstructed pilot orifice.  
3. Pilot gas turned off at automatic pilot.  
4. Problem with automatic pilot valve.  
1. Problem with thermocouple.  
2. Thermocouple not hot enough.  
3. Obstructed or wrong size pilot orifice.  
4. Gas supply not purged of air.  
5. Air blowing pilot out.  
6. Problem with automatic pilot valve.  
Fat appears to smoke excessively.  
Food sticks to griddle.  
1. Heat set too high.  
2. Moisture in food may be turning into steam.  
1. Heat set too high.  
2. Griddle surface needs cleaning and/or  
seasoning.  
3. Surface under food not covered with enough  
cooking oil.  
Food burned around edges or contains dark  
specks.  
1. Heat set too high.  
2. Griddle surface needs cleaning and/or  
seasoning.  
3. Surface under food not covered with enough  
cooking oil.  
Food undercooked inside.  
1. Heat set too high.  
2. Food not cooked for long enough time.  
Food tastes greasy or has objectionable off-  
flavor.  
1. Food itself may have off-flavor.  
2. Food stored improperly before cooking.  
3. Too much griddle fat used.  
4. Heat set too low.  
Noticeable build-up of gum on griddle.  
1. Heat set too high.  
2. Griddle surface needs cleaning and/or  
seasoning.  
3. Too much griddle fat used.  
FORM 30993 (10-96) (Formerly 990409)  
12 —  
 

Tascam Cassette Player 202mkIII User Manual
Tascam CD Player BB 800 User Manual
Teac Computer Drive FD 05PUB User Manual
The Singing Machine Karaoke Machine Singing Machine User Manual
Toshiba Copier 5520c User Manual
Toshiba Projection Television 50HM66 User Manual
Toshiba Projection Television 72MX196 User Manual
Tripp Lite Network Card UPS USB Adapter User Manual
ViewSonic Car Video System VG2039m User Manual
ViewSonic Tablet VPAD10 User Manual