Transition Networks Switch MIL SM8002TG User Manual

MIL-SM8002TG  
9 Port 10/100/1000BASE-T  
Two Combo 1000BASE-X SFP  
Ports  
Advanced Managed Switch  
Quick Installation Guide  
Rev.A  
09-MAY2006  
 
Introduction  
The product is a multi-port switch that can be used to build high-performance switched  
indoor or protected outdoor networks. It provides wire-speed, Gigabit Ethernet switching  
function that allows high-performance, low-cost connection. The Switch features a  
store-and-forward switching and it can automatically learn and store source address in an  
8K-entry MAC address table.  
Package Contents  
Unpack the contents of the switch and verify them against the checklist below.  
¢
¢
¢
¢
¢
Managed Switch unit  
Power Cord  
Four Rubber Feet  
RS-232 cable  
User Manual  
If any item is missing or damaged, please contact your local dealer for service.  
1
 
Hardware Description  
Physical Dimension  
The physical dimensions of the switch is 217mm(W) x 140mm(D) x 43mm(H)  
Desktop Installation  
Mount the switch on a desired space by either using wallmount brackets of rubber feet.  
Make sure there is enough clearance around the Switch to allow attachment of cables,  
power cord and air circulation.  
Power On  
Connect the power cord to the power socket on the rear panel of the Switch. The other  
side of power cord connects to the power outlet. The internal power works with AC in the  
voltage range 90-240VAC, frequency 50~60Hz. Check the power indicator on the front  
panel to see if power is properly supplied.  
2
 
Initial Setup  
Login in the Console Interface  
Use serial cable provided in the package to pre-configure the IP settings. When the  
connection between Switch and PC is ready, turn on the PC and run a terminal emulation  
program or Hyper Terminal and configure its communication parameters to match the  
following default characteristics of the console port:  
Baud Rate: 9600 bps  
Data Bits: 8  
Parity: none  
Stop Bit: 1  
Flow control: None  
The settings of communication parameters  
After finished the parameter settings, click “OK“. When the blank screen shows up, press  
Enter key to bring out the login prompt. Key in the “root“(default value) for the both User  
3
 
name and Password (use Enter key to switch), then press Enter key and the Main Menu  
of console management appears. Please see below figure for login screen.  
Console login interface  
IP/Subnet/Gateway Setup  
MIL-SM8002TG is shipped with a default IP of 192.168.1.77. In order to set up a customer  
specific IP/Subnet/Gateway Use Main menu – Type: “menu” – Select System  
Configuration – IP Configuration  
In the IP configuration window please choose the following:  
1. DHCP: disable or enable the DHCP client function. When DHCP function is enabled  
you don’t need to assign the IP address and subnet mask. The system will be  
4
 
assigned the IP address from the local DHCP server.  
2. IP Address: assign the switch IP address. The default IP is 192.168.16.1.  
3. Subnet Mask: assign the switch IP subnet mask.  
4. Gateway: assign the switch gateway. The default value is 192.168.16.254.  
5. DNS1: Optionally set up Domain Name Server  
6. DNS2: Optionally set up a backup for DNS1. When the DNS1 cannot function, the  
DNS2 can replace DNS1 immediately.  
7. Select <Save> action to save the configuration.  
[NOTE] Always restart the switch after finished the setup.  
Continue with web-based management for additional setup.  
6475 City West Pkwy  
Eden Prairie, MN 55344  
Tel.: +1.952.941.7600  
5
 

Taylor Scale 3840BL User Manual
Tektronix Printer Accessories 016 1103 00 User Manual
Toshiba Home Theater System SD 43HK User Manual
Toshiba Telephone CTX User Manual
Trane Air Conditioner UniTrane Fan Coil Force Flo Air Conditioners User Manual
Tripp Lite Power Supply 2009XXXXX 93 1350_EN User Manual
Turbo Chef Technologies Oven 3240TM User Manual
Turbosound Portable Speaker TXD series User Manual
Universal Smoke Alarm 1422 User Manual
VDO Dayton Automobile Accessories RV 5100 User Manual