Linksys Network Router RT31P2 VU User Manual

Config ure the Route r  
2
®
A Division of Cisco Systems, Inc.  
D
E
If you have a second phone  
line, repeat step C to connect  
a telephone or fax machine to  
the Router’s PHONE 2 port.  
There are two ways to configure the Router. Choose one of the following:  
In Step 2, you will need the setup  
instructions provided by your Internet  
Service Provider (ISP). If you do not  
have this information, then contact  
your ISP before proceeding.  
• Run the Setup CD-ROM - It is strongly recommended that you use the  
Setup CD-ROM. Insert the Setup CD-ROM into the CD-ROM drive, and  
follow the on-screen instructions.  
Connect your cable or DSL  
modem’s Ethernet cable to  
the Router’s Internet port. (If  
your modem only provides a  
USB output, then you will need  
to upgrade your modem.)  
The instructions from your ISP tell you  
how to set up your PC for Internet  
access. Because you are now using  
the Router to share Internet access  
among several computers, you will  
use the setup information to  
configure the Router instead of  
your PC.  
Use this Quick Installation guide - If you wish, you can use the Router’s  
Web-based Utility. Proceed to Step 1 of this Quick Installation.  
NOTE: Make sure your PCs  
Ethernet adapter is set to obtain  
an IP address automatically. For  
more information, refer to  
Windows Help.  
E
Conne c t the Route r  
1
F
Power on the cable or DSL  
modem.  
A
Make sure that all of your  
hardware is powered off,  
including the Router, PCs, and  
cable or DSL modem.  
G Connect the included power  
adapter to the Router’s Power  
port, and then plug the power  
adapter into an electrical  
outlet.  
A
Open your PC’s web browser.  
Router’s default local IP  
address) in the web browser’s  
Address field. Then press the  
Enter key.  
G
A
B
Connect one end of an  
Ethernet network cable to one  
of the numbered ports on the  
back of the Router. Connect  
the other end to an Ethernet  
port on a network device, e.g.,  
a PC, print server, or switch.  
The Power LED on the front  
panel will light up as soon as  
the power adapter is  
B
A screen will appear and ask  
you for a User Name and  
Password. Enter admin (the  
default) in the User Name and  
Password fields. (Later you  
should set a new password  
using the Administration tab’s  
Management screen. This will  
help secure access to the  
Web-based Utility.)  
connected properly.  
B
Package Contents  
H
Power on the PC you wish to  
use to configure the Router.  
Broadband Router with 2 Phone Ports  
Power Adapter  
Setup Wizard CD-ROM with Norton Internet Security  
• Installation and Troubleshooting Guide  
Network Cable  
Repeat this step to connect  
more PCs or other network  
devices to the Router.  
B
Telephone Jack Adapter  
Quick Installation  
C If necessary, disconnect the  
telephone cable from the  
telephone wall jack and  
Then click the OK button.  
connect that end to the  
telephone jack adapter. Then  
connect the adapter to the  
Router’s PHONE 1 port.  
Broadband Router  
C
with 2 Phone Ports  
NOTE: Make sure your telephone  
is set to its tone setting (not  
pulse).  
Quick Installation  
VoIP  
VoIP  
 
Model No.  
RT31P2-VU  

Lenmar Enterprises Battery Charger PPU5000 User Manual
Lenovo Personal Computer 10080 User Manual
LG Electronics Cell Phone VX5400 User Manual
LG Electronics CRT Television 29FX6ALX User Manual
LG Electronics Flat Panel Television OLED55B6P User Manual
Logitech Corded Headset H650e User Manual
Magic Chef Microwave Oven MCD18G1W User Manual
Makita Brush Cutter BCM2310 User Manual
McCulloch Lawn Mower M200117H User Manual
McCulloch Lawn Mower MC17107 User Manual