MODEL
MODÈLE
MODELO
#840013
3/8" VARIABLE SPEED ELECTRIC DRILL
INSTRUCTION MANUAL
MANUEL D’UTILISATION POUR PERCEUSE ÉLECTRIQUE
DE 3/8 PO À VITESSE VARIABLE
MANUAL DE INSTRUCCIONES SOBRE EL TALADRO ELÉCTRICO
DE 3/8" DE VELOCIDAD VARIABLE
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS
PRODUCT. BEFORE USE, READ CAREFULLY AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT
LABELS. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
CE MANUEL CONTIENT DES INFORMATIONS IMPORTANTES CONCERNANT LA SÉCURITÉ, LE FONCTIONNEMENT ET LE
REMISAGE DE CE PRODUIT. LIRE, ÉTUDIER ET VEILLER À BIEN COMPRENDRE TOUTES LES MISES EN GARDE ET INSTRUCTIONS
ET AUTOCOLLANTS APPOSÉS SUR LE PRODUIT AVANT DE L’UTILISER. NE PAS RESPECTER CES INSTRUCTIONS POURRAIT
ENTRAÎNER DES BLESSURES ET/OU DES DOMMAGES MATÉRIELS.
ESTE MANUAL CONTIENE INFORMACIÓN IMPORTANTE SOBRE LA SEGURIDAD, OPERACIÓN, MANTENIMIENTO Y ALMACE-
NAMIENTO DE ESTE PRODUCTO. ANTES DE USARLO, LEA Y COMPRENDA TODAS LAS PRECAUCIONES, ADVERTENCIAS,
INSTRUCCIONES Y ETIQUETAS DEL PRODUCTO. DE LO CONTRARIO PODRÍA SUFRIR LESIONES GRAVES O CAUSAR DAÑOS
MATERIALES.
87-1904-60957
IF YOU SHOULD HAVE ANY QUESTIONS OR EXPERIENCE A PROBLEM WITH YOUR ALLTRADE PRODUCT, DO NOT RETURN THIS
PRODUCT TO THE STORE. PLEASE CALL OUR CUSTOMER SERVICE DEPARTMENT AT 1-800-590-3723. BEFORE YOU CALL,
HAVE THE FOLLOWING INFORMATION AVAILABLE: MODEL No., DATE PURCHASED AND STORE LOCATION. AN ALLTRADE
REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU WOULD LIKE TO MAKE A SUGGESTION OR
KAWASAKI™ IS A TRADEMARK LICENSED BY KAWASAKI™
MOTORS CORP., U.S.A., WHICH DOES NOT MANUFACTURE OR
DISTRIBUTE THIS PRODUCT. CONSUMER INQUIRES SHOULD BE
DIRECTED TO:
KAWASAKI™ EST UNE MARQUE DE COMMERCE DE KAWASAKI™
MOTORS CORP., U.S.A., QUI NE FABRIQUE PAS ET NE DISTRIBUE
PAS CE PRODUIT THIS PRODUCT. LES QUESTIONS DES CONSOM-
MATEURS DOIVENT ÊTRE ADDRESSÉES À :
POUR TOUTE QUESTION OU EN CAS DE PROBLÈME AVEC LE PRODUIT ALLTRADE, NE PAS LE RETOURNER AU MAGASIN OÙ IL
A ÉTÉ ACHETÉ. APPELER LE SERVICE APRÈS-VENTEAU 1-800-590-3723. AVANT D’APPELER, VEILLER À SE PROCURER LES
INFORMATIONS SUIVANTES : No. DE MODÈLE, DATE DE L’ACHAT ET ADRESSE DU MAGASIN. UN REPRÉSENTANT D’ALLTRADE
PEUT RÉSOUDRE VOTRE PROBLÈME PAR TÉLÉPHONE. POUR TOUT COMMENTAIRE OU SUGGESTION, N’HÉSITEZ PAS À NOUS
APPELER OU NOUS CONTACTER PAR COURRIEL À L’ADRESSE : [email protected]. VOS COMMENTAIRES NOUS
SONT EXTRÊMEMENT PRÉCIEUX.
FOR CUSTOMER SERVICE
POUR LE SERVICE APRÉS VENTE
OU DU CONSOMMATEUR
KAWASAKI™ ES UNA MARCA REGISTRADA CON LICENCIA DE
KAWASAKI™ MOTORS CORP., E.U.A., QUE NO FABRICA NI
DISTRIBUYE ESTE PRODUCTO. LAS CONSULTAS DE LOS
CONSUMIDORES DEBEN DIRIGIRSE A:
PARA EL SERVICIO
PARA EL CONSUMIDOR
SI TIENE DUDAS O SURGEN PROBLEMAS CON SU PRODUCTO ALLTRADE, NO LO DEVUELVA A LA TIENDA LLAME A NUESTRO
DEPARTAMENTO DE SERVICIO AL CLIENTE AL 1-800-590-3723. ANTES DE LLAMAR, TENGA A MANO LA SIGUIENTE
INFORMACIÓN: No. DE MODELO, FECHA DE COMPRA Y DIRECCIÓN DE LA TIENDA. UN REPRESENTANTE DE ALLTRADE PUEDE
RESOLVER SU PROBLEMA POR TELÉFONO. SI DESEA HACER ALGUNA SUGERENCIA O COMENTARIO, LLÁMENOS O ENVÍENOS
UN MENSAJE DE CORREO ELECTRÓNICO A. INFO@ALLTRADETOOLS.COM. SUS COMENTARIOS SON FUNDAMENTALES PARA
NOSOTROS.
©COPYRIGHT 2006 ALLTRADE TOOLS, LLC.
1431 VIA PLATA
LONG BEACH, CA 90810-1462 USA
1-800-590-3723
Printed in China
Imprimé dans la Chine
Impreso en China
840013 – 3/8" Variable Speed Electric Drill, PERCEUSE ÉLECTRIQUE
DE 3/8 PO À VITESSE VARIABLE, TALADRO ELÉCTRICO DE 3/8" DE
VELOCIDAD VARIABLE _Rev. 5/10/06
WORK AREA
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injury.
Keep your work area clean and well lit. Cluttered work benches and dark work
areas may cause accidents or injury.
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation which,
if not avoided, may result in property damage.
Do not operate power tools in explosive areas, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks which may ignite
the dust or fumes.
NOTE provides additional information that is useful
for proper use and maintenance of this tool. If a
NOTE is indicated make sure it is fully understood.
Keep bystanders, children and visitors away while operating a power tool.
Distractions can cause you to lose control.
IMPORTANT SAFEGUARDS
ELECTRICAL SAFETY
People with electronic devices, such as pacemakers, should consult their
physician(s) before using this product. Operation of electrical equipment in
close proximity to a heart pacemaker could cause interference or failure of
the pacemaker.
Double insulated tools are equipped with a polarized plug (one blade is
wider than the other.) This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician to install a polarized outlet. Do not change the
plug in any way. Double insulation eliminates the need for the three wire
grounded power cord and grounded power supply system.
WARNING: Some dust created by power sanding, sawing, grinding, drilling and
other construction activities contains chemicals known to the State of California
to cause cancer, birth defects or other reproductive harm.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased risk of electric shock if your body is
grounded.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonry products,
and arsenic and chromium from chemically-treated lumber.
Don’t expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
Your risk from these exposures varies, depending on how often you do this type
of work. To reduce your exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such as dust masks that are
specially designed to filter out microscopic particles.
Do not abuse the cord. Never use the cord to carry the tool or pull the plug
from an outlet. Keep the cord away from heat, oil, sharp edges, or moving
parts. Replace damaged cords immediately. Damaged cords increase the risk
of electric shock.
WARNING: Handling the power cord on this product may expose you to lead, a
chemical known to the State of California to cause cancer and birth defects or
other reproductive harm. Wash hands after handling.
When operating the tool outside, use an outdoor extension cord marked “W-
A” or “W.”These cords are rated for outdoor use and reduce the risk of elec-
tric shock.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
3
4
Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained
tools with a sharp cutting edge are less likely to bind and are easier to control.
PERSONAL SAFETY
Check for misalignment or binding of moving parts, breakage of parts, and any
other condition that may affect the tool’s operation. If damaged, have the tool
serviced before using.
Stay alert, watch what you are doing, and use common sense when operat-
ing a power tool. Do not use tool while tired or under the influence of drugs,
alcohol or medication. A moment of inattention while operating power tools
may result in serious personal injury.
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool, may become hazardous when used
on another tool.
Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewelry or long hair can be caught in moving parts.
SERVICE
Tool service must be performed only by qualified repair personnel. Service or
maintenance by unqualified personnel could result in a risk of injury.
Avoid accidental starting. Be sure switch is off before plugging in. Carrying
tools with your finger on the switch or plugging in tools that have the switch on invites
accidents.
When servicing a tool, use only identical replacement parts. Follow instructions
in the Maintenance section of this manual. Use of unauthorized parts or failure to
follow Maintenance Instructions may create a risk of shock or injury.
Remove adjusting keys or wrenches before turning the power tool “ON”.
A wrench or a key that is left attached to a rotating part of the power tool may
result in personal injury.
SPECIFIC SAFETY RULES AND/OR SYMBOLS
Do not overreach. Keep proper footing and balance at all times. Proper foot-
ing and balance enables better control of the power tool in unexpected situa-
tions.
Hold tool by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring. Contact with a “live” wire will also make
exposed metal parts of the tool “live” and shock the operator.
Use safety equipment. Always wear eye protection. Dust mask, non-skid
safety shoes, hard hat or hearing protection must be used for appropriate
conditions.
IMPORTANT SAFETY RULES FOR DRILLS
For safety and better control, always use both hands to hold tool. If the bit jams and
kicks back, having both hands on the drill will make it easier to handle.
TOOL USE AND CARE
Always wear eye protection and an OSHA-approved dust mask when drilling.
Use clamps or other practical ways to secure and support the workpiece to a
stable platform. Holding the work by hand or against your body is unstable and
may lead to loss of control.
Never hold the work piece in your hand or against your body. Use clamps to anchor
the work piece to a stable base. Never drill material too small to be secured properly.
Do not force tool. Use the correct tool for your application. The correct tool will
do the job better and safer at the rate for which it is designed.
Keep hands and drill cord away from the rotating bit.
Make sure there are no nails, staples or other foreign objects in the work piece.
Do not use the tool if the power switch does not turn it “ON” or “OFF”. Any tool that
cannot be controlled with the switch is dangerous and must be repaired.
To prevent accidental starting, always disconnect the plug from the power source
before making any adjustments or changing accessories.
Disconnect the power cord plug from the power source before making any
adjustments, changing accessories or storing the tool. Such preventive safety
measures reduce the risk of starting the tool accidentally.
Never run the drill while carrying it at your side.
If the bit becomes bound in the work piece, release the trigger immediately and
prepare for the tool to kickback toward you. Reverse the direction of rotation, then
back out the bit by slowly squeezing the trigger.
Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.
5
6
Make sure all accessories are rated for the recommended speed of the drill.
Brushes, grinding wheels and other accessories may fall apart if run at too high a
speed, sending dangerous debris flying at the operator.
FUNCTIONAL DESCRIPTION
Use gloves when changing hot bits and accessories to avoid burns.
1
SYMBOLS
IMPORTANT: Some of the following symbols may be used on your tool. Please
study them and learn their meaning. Proper interpretation of these symbols will
allow you to operate the tool better and safer.
SYMBOL
NAME
Volts
Amperes
Hertz
Watt
Kilograms
Alternating Current
Direct Current
EXPLANATION
Voltage (Potential)
Current
Frequency (Cycles per Second)
Power
Weight
Type of Current
Type of Current
2
V
A
Hz
W
Kg
Alternating or Direct Current Type of Current
Earthing Terminal
Class II Construction
Minutes
Grounding Terminal
Denotes Double Insulation
Time
Time
min
s
Seconds
CONTROLS AND COMPONENTS:
1. 3/8" Variable Speed Drill
Diameter
Size of Drill Bits,
Grinding Wheels, etc.
2. Chuck Key
No load speed
No-load Rotational Speed
.../min
Revolutions per Minute
Revolutions, Surface Speed,
Strokes, etc. per Minute
OPERATING INSTRUCTIONS
1,2,3, …
Ring Selector Settings
Speed, Torque or Position Settings
Disconnect the power plug from the AC power source
before any assembly, adjustments, or adding/removing accessories.
Following this preventative step reduces the risk of the drill coming on acciden-
tally and the risk of damage to the workpiece and injury to the operator.
8
7
BIT INSERTION
• Unplug the drill. Never change bits
OPERATING THE ON/OFF SWITCH
Squeeze the trigger switch to turn the tool “ON”. Release the trigger switch to turn
the tool “OFF”.
on a live drill.
• Make sure the bit is undamaged,
sharp and free from wood or metal
shavings. Foreign material on the
bit may keep the chuck from tight-
ening fully. A loose bit may cause
injury.
When drilling for extended periods, the “Lock-On” switch may be used, but do not
use this switch in situations where the drill is likely to bind or kickback. If kickback
does occur, the sudden motion of the tool may make it difficult to release the “Lock-
On” switch and turn the drill off.
SPEED CONTROL ADJUSTING SWITCH
• Push the bit into the chuck as far
as it will go.
To increase the operating speed of the
drill, turn the variable speed control clock-
wise. To decrease the speed, turn the
variable speed control counterclockwise.
• Make sure the bit is in the center
of the chuck. If the bit is off-cen-
ter, it will not be held securely and
may fly loose during use causing
serious injury.
• Insert the chuck key into one of the three chuck holes. Rotate the chuck key
clockwise to lock the bit in place.
• Remove the chuck key.
Always run the drill for one minute before drilling to make
sure the bit is properly seated. If the bit needs to be adjusted, unplug the drill
before touching the bit.
REVERSING SWITCH LEVER
The reversing switch lever reverses the
rotation of the drill bit. It is located just
above the trigger switch. ALWAYS turn the
motor off and let the bit come to a
complete stop before moving the switch.
BIT REMOVAL
• Unplug the drill.
Move the switch to the right for a forward
rotation of the bit. Move the switch to the
left to put the bit into reverse.
• Insert the chuck key into one of
the three chuck holes. Rotate the
chuck key counterclockwise to
unlock the bit.
• Remove the bit.
Do not change the direction of a moving bit. Make sure the
bit comes to a complete standstill before moving switch. Changing direction
while the bit is moving can cause damage to the drill.
9
10
MAINTENANCE AND CLEANING
In certain situations, the bit may bind and the drill will kick-
back in the opposite direction. This sudden reaction could lead to loss of con-
trol and possible serious injury. Always be prepared for the possibility of kick-
back, especially when breaking through material to complete a hole.
Unplug the drill before performing maintenance or cleaning.
• Never immerse tool in liquid. Never let any liquid inside tool housing.
• Clean with a damp cloth and mild soap. Do not use solvents or harsh detergents.
• Check brushes periodically. Worn brushes should be replaced by qualified serv-
ice personnel.
DRILLING WOOD
• Always clamp the work piece to a steady base. Never hold in your hand or
across your legs.
• Keep air vents clean and free from debris. Blocked air vents can lead to over-
heating.
• Apply pressure in line with the bit. Applying pressure at an angle could cause
the bit to bind or break.
ACCESSORIES
• Thin materials that may splinter should be drilled with another piece of wood
placed underneath.
Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
• Twist bits can be used for wood drilling but will overheat if the flutes are not
cleared of wood chips periodically.
Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets.
• To prevent splintering when finishing holes, stop drilling just before the hole
breaks through and complete the hole from the other side.
If you must use an extension cord, be sure that the gauge is large enough to carry
the amount of current necessary for your power tool. If not, your tool may experi-
ence a loss of power, excessive voltage drop or overheating. The smaller the gauge
number, the heavier the cord (see table below).
DRILLING MASONRY
• Always use carbide tip bits for drilling masonry.
RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS
• Use an even pressure, hard enough to keep the drill biting, but not so hard that
the bit spins in the hole. Spinning the bit will dull it quickly. Bricks and similar
soft materials will take less pressure than a hard material like concrete.
TOOL CURRENT RATING
CONDUCTOR SIZE IN A.W.G
AMPERE
3-6
6-8
8-10
10-12
12-16
16-20
10FT.
18
18
18
16
25FT.
18
18
18
16
50FT.
18
18
18
14
100FT.
18
16
14
14
-
DRILLING METAL
• Use an even pressure, hard enough to keep the drill biting, but not so hard that
the bit spins in the hole. Spinning the bit will dull it quickly. Soft metals like
copper, cast iron, brass or aluminum will take less pressure than harder
materials like steel.
14
12
12
12
12
12
-
• When drilling harder metals, use lubricating oil on the tip of the bit.
11
12
date the original purchaser took possession, custody or control of the product,
whichever occurred first. This warranty shall be null and void if the product or any
component thereof is modified, altered or used for any commercial purpose or on
a jobsite. This warranty does not apply to any other product and/or component
thereof manufactured or distributed by Alltrade, and does not apply to products
and/or components thereof designed, manufactured and/or assembled by others,
for which Alltrade makes no warranties whatsoever. THERE ARE NO WARRANTIES
WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
SPECIFICATIONS
SPECIFICATIONS
Voltage
Rated Current
No-Load Speed
Chuck Capacity (max.)
120V
60 Hz
3.3 A
0-2700/min
10mm (3/8")
Warranty Performance
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS
By purchasing the product, purchaser expressly acknowledges and agrees that their
sole and exclusive remedy under this warranty shall be strictly limited to the repair
or replacement of any covered nonconforming items or parts thereof provided that
any such nonconforming item and/or part is promptly returned to Alltrade’s facility
postage pre-paid and insured (address: ALLTRADE Warranty Claims & Repair,
1431 Via Plata, Long Beach, CA 90810, Attn: Customer Service #1-800-590-3723)
within the applicable warranty period, with a written request by purchaser that
Alltrade repair and/or replace the nonconforming item and/or part. We recommend
that you keep the original product packaging in the event you need to ship the unit.
We suggest the package be insured against loss or in transit damage. When
sending your product include your name, address, phone number, dated proof
of purchase (or copy), and a statement about the nature of problem. Warranty
coverage is conditioned upon purchaser furnishing Alltrade with adequate written
proof that they are the original purchaser and of the original purchase date. Parts
returned, freight prepaid and insured, to Alltrade’s facility (see above address) will
be inspected and, at Alltrade’s option, repaired and/or replaced free of charge if
found to be defective and subject to warranty. Alltrade retains the sole discretion
to determine whether any item or part is nonconforming and, if so, whether the
item and/or part will be repaired and/or replaced. If the unit is repaired, new or
reconditioned replacement parts may be used. If Alltrade chooses to replace
the product, it may replace it with a new or reconditioned one of the same or
comparable design. The repaired or replaced unit will be warranted under the terms
of the remainder of the warranty period. Typically, a defective product that is
returned within the first 30 days after the purchase date will be replaced; for items
returned after the first 30 days and within the warranty period, covered defective
parts not subject to normal wear and tear or other exclusions will be repaired or
replaced, at Alltrade’s option. During the warranty period, Alltrade will be responsi-
ble for the return shipping charges. Alltrade’s repair and/or replacement of any non-
conforming item and/or part thereof shall constitute fulfillment of all
obligations to the purchaser. Alltrade shall not be responsible or liable for any
expense, including freight charges, or repairs made outside Alltrade’s facility, unless
expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade
bear any responsibility for loss of the unit, loss of time or rental, inconvenience,
commercial loss or consequential damages.
Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would
like further information on the following products, please contact Alltrade Customer
Service Department at 1-800-590-3723.
Cordless Drills/Screwdrivers
Impact Wrenches
Sanders
Jigsaws
Circular Saws
Angle Grinders
Reciprocating Saws
Routers
Rotary Tools
Corded and Cordless Multi-Purpose Tools
Wide Range of Accessories and more
2 YEAR LIMITED HOME USE WARRANTY
Express and Exclusive Limited Home Use Warranty to Original Retail Buyer
Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail
purchaser of the accompanying KAWASAKI™ portable power tool and no one else
all parts of the product (except those parts referred to below which are specifically
excluded from such warranty (see Exclusions)) to be free from defects in materials
and workmanship for a period of two years from original date of purchase.
SPECIAL WARRANTY NOTE TO CONTRACTORS AND COMMERCIAL USERS: This
Kawasaki™ portable power tool is offered as a home use tool and carries a HOME
USE WARRANTY. This tool is made for home use in the execution of
projects and repairs in and around the home. Use of the tool for COMMERCIAL
PURPOSES OR ON A JOBSITE is not covered under this warranty.
The date of purchase shall be the date of shipment to the original purchaser, or the
13
14
Exclusions
WARRANTY IS MADE WITH REGARD TO THIS PRODUCT. ALL EXPRESS AND/OR
IMPLIED WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS BY ALLTRADE
AND/OR ITS REPRESENTATIVE(S) REGARDING THE DESIGN, MANUFACTURE,
PURCHASE, USE AND/OR OPERATION OF THE PRODUCT OR ANY COMPONENT
THEREOF SOLD HEREUNDER, REGARDLESS OF WHETHER ANY SUCH WARRANTY,
GUARANTY AND/OR REPRESENTATION, WRITTEN OR ORAL, ARISES BY
OPERATION OF LAW AND/OR EQUITY AND/OR BY ANY ACT OR OMISSION OF
ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE PURCHASER, INCLUDING
BUT NOT LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY EXPRESSLY
EXCLUDED AND DISCLAIMED BY ALLTRADE AND/OR ITS REPRESENTATIVES.
PURCHASER KNOWINGLY AND WILLINGLY WAIVES ANY AND ALL SUCH
WARRANTIES AND RIGHTS, CLAIMS AND/OR CAUSES OF ACTION ARISING
THEREFROM OR BASED THEREON. PURCHASER’S SOLE AND EXCLUSIVE
REMEDY IS AS STATED ABOVE.
This warranty does not cover parts damaged due to normal wear, abnormal
conditions, misapplication, misuse, abuse, accidents, operation at other than
recommended pressures or temperatures, improper storage or freight damage.
Parts damaged or worn by operation in dusty environments are not warranted.
Failure to follow recommended operating and maintenance procedures also
voids warranty.
This limited warranty does not apply to accessory items such as drill bits,
screwdriving bits, circular saw blades, jigsaw blades, grinding wheels, sanding
sheets and other related items.
DAMAGE TO THE PRODUCT RESULTING FROM TAMPERING, ACCIDENT, ABUSE,
NEGLIGENCE, FAILURE TO FOLLOW INSTRUCTIONS, UNAUTHORIZED REPAIRS
OR ALTERATIONS, DAMAGE WHILE IN TRANSIT TO OUR SERVICE FACILITY,
USE OF UNAPPROVED OR IMPROPER ATTACHMENTS OR ACCESSORIES,
COMMERCIAL AND RENTAL APPLICATIONS OR OTHER CAUSES UNRELATED TO
PROBLEMS WITH MATERIAL OR WORKMANSHIP ARE NOT COVERED BY THIS
WARRANTY.
Limitation Of Liability
IN NO EVENT SHALL ALLTRADE AND/OR ITS REPRESENTATIVE(S) BE LIABLE FOR
INDIRECT, INCIDENTAL, SPECIAL AND/OR CONSEQUENTIAL DAMAGES OF ANY
KIND ARISING OUT OF OR RELATED TO, DIRECTLY OR INDIRECTLY, ANY BREACH
OF ANY PROVISION OF ANY AGREEMENT BETWEEN ALLTRADE AND/OR ITS
REPRESENTATIVE(S) AND PURCHASER, ANY WARRANTY HEREUNDER,
AND/OR THE EXISTENCE, DESIGN, MANUFACTURE, PURCHASE, USE AND/OR
OPERATION OF ANY ITEM(S) SOLD HEREUNDER EVEN IF ALLTRADE AND/OR ITS
REPRESENTATIVE(S) HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH
DAMAGES. IN NO EVENT, WHETHER AS A RESULT OF A BREACH OF CONTRACT,
WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL
ALLTRADE’S AND/OR ITS REPRESENTATIVE(S)’ LIABILITY EXCEED THE PRICE OF
THE PRODUCT. ANY AND ALL LIABILITY CONNECTED WITH THE USE OF
THIS PRODUCT SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY
PERIODS SPECIFIED ABOVE.
Alltrade will not be liable for the following: labor charges, loss or damage resulting
from improper operation, maintenance or repairs made by other persons;
pre-delivery services such as assembly, oil or lubricants, and adjustment;
maintenance services that are normally required to maintain the product.
The use of other than genuine Alltrade Repair Parts will void warranty.
Warranty Disclaimers
EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES,
GUARANTIES AND/OR REPRESENTATIONS. EXCEPT FOR THE LIMITED WARRANTY
PROVIDED ABOVE, ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR
REPRESENTATIONS BY ALLTRADE AND/OR ITS REPRESENTATIVE(S) REGARDING
THE DESIGN, MANUFACTURE, PURCHASE, USE AND/OR OPERATION OF THE
PRODUCT OR ANY COMPONENT THEREOF SOLD HEREUNDER, REGARDLESS OF
WHETHER ANY SUCH WARRANTY, GUARANTY AND/OR REPRESENTATION,
WRITTEN OR ORAL, ARISES BY OPERATION OF LAW AND/OR EQUITY AND/OR BY
ANY ACT OR OMISSION OF ALLTRADE AND/OR ITS REPRESENTATIVE(S), OR THE
BUYER, ARE HEREBY EXPRESSLY EXCLUDED AND DISCLAIMED BY ALLTRADE
AND/OR ITS REPRESENTATIVES. PURCHASER KNOWINGLY AND WILLINGLY
WAIVES ANY AND ALL SUCH WARRANTIES AND RIGHTS, CLAIMS AND/OR
CAUSES OF ACTION ARISING THEREFROM OR BASED THEREON. PURCHASER’S
SOLE AND EXCLUSIVE REMEDY IS AS STATED ABOVE.
Limitations on Warranty Disclaimers
Some states do not allow limitations on how long an implied warranty lasts
and some states do not allow the exclusion or limitation of the incidental or
consequential damages, so part or all of the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
If your product is not covered by this warranty, please call our Customer Service
Department toll free at 1-800-590-3723 for general repair information and charges.
EXCLUSION AND DISCLAIMER OF ALL IMPLIED WARRANTIES, INCLUDING THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO WARRANTY, ORAL OR WRITTEN, OTHER THAN THE ABOVE
15
16
|