Infinity Portable Speaker TSS 3 IN 1 User Manual

TSS 3-IN-1  
TOTAL SPEAKER SOLUTIONS  
TSS 3-IN-1  
Owner’s Guide  
 
Tilting the Speaker  
Wall-Mounting the TSS 3-IN-1 Using the Included  
Wall Bracket  
The customer is responsible for proper selection and use of  
mounting hardware, and for correctly and safely wall-mounting  
the speakers.  
If needed, the enclosed stand allows you to tilt the speaker  
across a wide range (i.e., upward to a maximum of 18˚ or  
downward to a maximum of 7˚), as shown in Figure 3.  
Important!  
Do not exceed the tilt range. Doing so may cause the speaker to  
fall out of its stand.  
Step One  
Remove the wall bracket cover by removing the four wall-bracket  
screws on the ends, as shown.  
Step Two  
Run the speaker wire for the left, center and right channels behind  
the wall bracket and out the holes in the bracket. After deciding  
where to place the speaker, attach the wall bracket (in a horizontal  
position) to the wall using the appropriate screws and anchors.  
Wall bracket  
Figure 3.  
Mounting screws and  
anchors not included  
Step Three  
Run the speaker wires out through the holes in the wall  
bracket cover. Resecure in place, as shown, with the four  
wall bracket screws.  
3
TSS 3-IN-1  
 
Step Six  
Step Four  
The wall-bracket design allows for rotation of the speakers  
at angles of up to 30 degrees of center. Position the speakers  
so they face toward the primary listening position, before  
fully tightening.  
Using the included Allen wrench, remove the top and bottom  
end caps of the speaker by unscrewing the single center screw  
on bottom.  
End cap  
End cap  
1/4-20 x 3/4"  
Screw  
Step Five  
Connect the wires (see page 5). Replace the end caps while  
capturing the wall bracket between parts A and B of the  
end cap, securing it in place.  
Wall-mount  
end cap B  
Wall-mount  
end cap A  
4
TSS 3-IN-1  
 
WIRING THE SPEAKER  
After placing the speaker, you are ready to connect it to your  
system. First, turn off all audio system power. Use high-quality  
speaker wire to make the connections. Consult the owner’s  
manuals included with your amplifier or receiver for connection  
and operation procedures.  
Surround Modes  
One channel shown.  
When using the TSS 3-in-1 in a Dolby® Digital or DTS® home  
theater system, make sure the receiver’s/processor’s front left,  
front right and center channel speaker modes are set toSmall.”  
Wiring and Polarity  
+
The TSS 3-in-1 speaker has gold-plated terminals that can  
accept bare wire.To ensure proper polarity, connect each  
+ terminal on the back of the amplifier or receiver to the  
respective + (red) terminal on each speaker, as shown in  
Figure 4. Connect the – (black) terminals in a similar way.  
See the owner’s manuals that were included with your  
amplifier or receiver to confirm connection procedures.  
Figure 4.This example shows how to connect bare wires to the  
terminals. Banana plugs may also be inserted directly into the  
rear of the connector.  
Loosen the terminals.  
Insert bare ends; tighten terminals.  
Be sure to connect the left-channel wires to the left-most  
terminals, the center channel wires to the middle terminals, and  
the right-channel wires to the right-most terminals.  
CARE OF YOUR SPEAKER SYSTEM  
When needed, use a soft cloth to remove any fingerprints or  
to wipe off dust. Do not use any cleaning products or polish.  
Clean the grille by gentle vacuuming.  
Important!  
Do not reverse polarities (i.e., + to – or – to +) when making  
connections. Doing so will degrade the imaging and bass  
response of the home theater system.  
If your TSS 3-in-1 should ever need service, please contact your  
the location of a service center.  
After correctly placing and wiring the TSS 3-in-1 and the rest of  
your speaker system, adjust the levels for all of the channels as  
recommended by the manufacturer of your receiver/processor.  
5
TSS 3-IN-1  
 
SPECIFICATIONS  
TSS 3-IN-1  
Each Channel  
Frequency Response  
120 – 20kHz ( 3dB)  
Nominal Impedance  
8 Ohms  
89dB  
Sensitivity  
(2.83V @ 1m)  
Recommended Amplifier  
Power Range  
10 – 125 Watts  
Crossover Frequency  
3,500Hz; 24dB/octave  
Low-Frequency Drivers  
(2) 3-1/2" (89mm) MMD®,  
magnetically shielded  
High-Frequency Driver  
3/4" (19mm) MMD,  
elliptical waveguide,  
magnetically shielded  
Dimensions (H x W x D)  
Weight  
4-1/8" x 40-1/8" x 4-3/8"  
(105mm x 1019mm x 111mm)  
15.25 lb (6.9kg)  
Infinity continually strives to update and improve existing products, as  
well as create new ones.The specifications and construction details in  
this and related Infinity publications are therefore subject to change  
without notice.  
Declaration of Conformity  
We, Harman Consumer Group International  
2, route de Tours  
72500 Château du Loir  
France  
declare in own responsibility that the product described in this  
owner’s manual is in compliance with technical standards:  
EN 61000-6-3:2001  
EN 61000-6-1:2001  
Laurent Rault  
Harman Consumer Group International  
Château du Loir, France 5/06  
6
TSS 3-IN-1  
 
NOTES  
 
Infinity Systems, 250 Crossways Park Drive,Woodbury, NY 11797 USA (516) 674-4463 (USA only) www.infinitysystems.com  
Infinity, Harman International and MMD are registered trademarks, and Total Solutions is a trademark, of Harman International Industries, Incorporated.  
Dolby is a registered trademark of Dolby Laboratories. DTS is a registered trademark of DTS, Inc.  
Part No. ML-TS40LCR 5/06  
© 2006 Harman International Industries, Incorporated.All rights reserved.  
 

Intellinet Network Solutions Switch 524100 User Manual
Iron A Way Iron A 42 User Manual
Ives Indoor Furnishings VR900 User Manual
John Deere Compact Excavator 350D LC User Manual
JVC VCR HM DH5U User Manual
Kenmore Sander 808353 User Manual
Kenwood Network Hardware TS 990S User Manual
Keys Fitness Treadmill Keys 9000LI User Manual
KitchenAid Clothes Dryer KHGV01R User Manual
Kodak Film Camera 5219 User Manual